technical data sheet rpc-tnc open circuit jack 06K12L-000S3 rosenberger hochfrequenztechnik gmbh & co. kg p.o.box 1260 d-84526 tittmoning germany www.rosenberger.de tel. : +49 8684 18-0 email : info@rosenberger.de page 1 / 3 dieses dokument ist urheberrechtlich geschtzt this document is protected by copyright rosenberger hochfrequenztechnik gmbh & co. kg rf_35/09.14/6.2 all dimensions are in mm; tolerances according to i so 2768 m-h interface according to iec 61169-26 documents application note an001 calibration services material and plating connector parts material plating center conductor cube gold, min. 1.27 m, over nickel outer conductor stainless steel passivated dielectric ptfe / ps
technical data sheet rpc-tnc open circuit jack 06K12L-000S3 rosenberger hochfrequenztechnik gmbh & co. kg p.o.box 1260 d-84526 tittmoning germany www.rosenberger.de tel. : +49 8684 18-0 email : info@rosenberger.de page 2 / 3 dieses dokument ist urheberrechtlich geschtzt this document is protected by copyright rosenberger hochfrequenztechnik gmbh & co. kg rf_35/09.14/6.2 electrical data frequency range dc to 18 ghz return loss 0.50 db, dc to 4 ghz 1.00 db, 4 ghz to 18 ghz error from nominal phase 1 3.5, dc to 4 ghz 5.0, 4 ghz to 8 ghz 8.0, 8 ghz to 18 ghz 1 the nominal phase is defined by the offset delay, the offset loss and the fringing capacitances. mechanical data mating cycles 3 500 maximum torque 1.70 nm recommended torque 0.55 nm gauge 5.18 mm to 5.28 mm general standard definitions for proper operation the vector network analyzer (v na) needs a model describing the electrical behavio ur of this calibration standard. the different models, units, and terms used will depend on the vna type and they will have to be entered into the vna. all valu es are based on typical geometry and plating. offset z o / impedance / z o 50 w offset delay 58.374 ps length (electrical) / offset length 17.50 mm offset loss 1.20 g ? /s loss 0.0122 db/ ghz fringing capacitances 2 2 fringing capacitances are determined individually for each open circuit and are documented in a calib ration certificate. environmental data operating temperature range 3 + 20 c to +26 c rated temperature range of use 4 0 c to +50 c storage temperature range - 40 c to +85 c rohs compliant 3 temperature range over which these specification ar e valid. 4 this range is underneath and above the operating te mperature range, within the open circuit is fully f unctional and could be used without damage.
technical data sheet rpc-tnc open circuit jack 06K12L-000S3 rosenberger hochfrequenztechnik gmbh & co. kg p.o.box 1260 d-84526 tittmoning germany www.rosenberger.de tel. : +49 8684 18-0 email : info@rosenberger.de page 3 / 3 dieses dokument ist urheberrechtlich geschtzt this document is protected by copyright rosenberger hochfrequenztechnik gmbh & co. kg rf_35/09.14/6.2 declaration of calibration options factory calibration standard delivery for this calibration standard inc ludes a factory calibration. the calibration certif icate issued reports individual calibration results, traceable to rosenberger standards , national / international standards are not available. model based standard d efinitions are individually optimized and reported in an agilent/keysight, rohde & schwarz and anritsu compa tible vna format. accredited calibration not available. for further, more detailed information see applicat ion note an001 on the rosenberger homepage. calibration interval recommendation 12 months packing standard 1 pce in box weight 40 g/pce draft date approved date rev. engineering change n umber name date herbert babinger 02.12.04 markus mller 22.04.16 c 00 16-s067 marcel panicke 22.04.16 while the information has been carefully compiled t o the best of our knowledge, nothing is intended as representation or warr anty on our part and no statement herein shall be construed as recommendation to infringe existing patents. i n the effort to improve our products, we reserve the right to make changes judg ed to be necessary.
|
